Cart
Checkout Secure

Coupon Code: FT68LD435 Copy Code

your country 

Got a Question? Call Us

1-877-780-6699

Mon-Fri 9am-5pm Central

Campania International Auberge Wall Fountain Assembly Instructions

Campania International Auberge Wall Fountain Assembly Instructions

  • 1. Make sure you are assembling your fountain on a level surface capable of holding a minimum of 555 pounds with approximately a 2.25 square foot footprint.
  • 2. Feed the pump and light cords through the hole in the basin leaving enough cord length inside basin to work with pump and light. a. The light will be resting on top of the disc inside the basin.
  • 3. Wrap a piece of putty around the cords where you will be placing the stopper. Fig A
  • 4. Fit cords into stopper.
  • 5. Place a piece of putty inside the length of the slit in the stopper. Fig B 6. Wrap putty around outside of stopper ensuring that the slit and the cord hole are covered and sealed. 7. Press stopper firmly into the hole of basin. 8. Make sure the appropriate 1/2” diameter enclosed fitting (the one shown in the middle of Fig C is inserted into the pump water outlet. Fittings are found in the pump box. a. Remove the small fitting as shown in Fig D. 9. Insert the ½” fitting into the hole in the pump as shown in Fig E. Place a hose clamp over the end of the ½ ” black non-kink tubing. 10. Insert that end of the ½ ”
  • 7. Press stopper firmly into the hole of basin.
  • 8. Make sure the appropriate 1/2” diameter enclosed fitting (the one shown in the middle of Fig C is inserted into the pump water outlet. Fittings are found in the pump box. a. Remove the small fitting as shown in Fig D. 9. Insert the ½” fitting into the hole in the pump as shown in Fig E. Place a hose clamp over the end of the ½ ” black non-kink tubing. 10. Insert that end of the ½ ”
  • 9. Insert the ½” fitting into the hole in the pump as shown in Fig E. Place a hose clamp over the end of the ½ ” black non-kink tubing. 10. Insert that end of the ½ ”
  • 9. Insert the ½” fitting into the hole in the pump as shown in Fig E. Place a hose clamp over the end of the ½ ” black non-kink tubing.
  • 10. Insert that end of the ½ ” non kink tubing onto the pump water outlet.
  • 11. Place another hose clamp onto the 5/8” clear tube connected to the ½” non-kink tubing. a. Note – the third hose clamp may be placed on the tubing prior to installation as a flow restrictor if necessary.
  • 12. Place the 5/8” clear tube end of the tubing onto the copper pipe extending out from the basin.
  • 13. Tighten the hose clamps on the ends of the tubing.
  • 14. Fill basin with approximately 11 gallons of water. a. Note – do not allow pump to run dry as it will cause damage to the pump.
  • 15. Place LED light in on top of the disc inside the basin aiming the light at the waterfall.

General Instructions for installing the Campania International Auberge Wall Fountain

Install the Auberge Wall Fountain on a level surface. You will need a properly grounded 110-volt (AC only) GFCI protected receptacle near the fountain for your pump. All pumps are submersible and must be completely underwater to function properly. Test all pumps and adjust to full output prior to assembly. It is not recommended that fountains be placed directly on grass or dirt. Position the channel opening at the base of each fountain toward the electrical.  

Campania International Auberge Wall Fountain Assembly Instructions

Campania International Auberge Wall Fountain Assembly Instructions part 2

Added to cart!

10% off !

When you complete your order in next:

SHOP NOW

OR

enter promo code SAVE10 at the CHECKOUT

Sitewide Free Shipping All Home & Garden Decor Ships Free in the US. Free Shipping For Over $x to